Product details

Home

UAP-04Paver


feature img1

MADE: Uniter Engineering Products

OVERVIEW:

Paver machines with hydraulically extendable screed and manual control for grade and slope control.

Material Laying Capacity: 100 TPH
Engine Power: 76 hp
Screed size: 2.5m to 4.5m
Wheels on rear axle: One on each side

FEATURES:

PRIME MOVER

  • Kirloskar make water-cooled electric start Diesel Engine Model 4R 1040T (76 hp @ 2300 rpm) or equivalent

  • Engine has sufficient space on all the sides for air draft and cooling of engine

  • Engine is easily accessible for daily maintenance like checking engine oil, coolant water level, engine suction filter etc

  • Engine starter, alternator can be easily removed for periodic maintenance.

  • Gauges like engine temperature, oil pressure and ampere meter are on sliding panel and are easily visible from operator’s seat.

POWER DISTRIBUTION GEAR BOX

  • N/A

HYDRAULICS

  • All hydraulic pumps, motors and hose pipes are of reputed make.

  • Utmost care has been taken in selection of joints so as to minimize chances of hydraulic oil leakage.

  • All ‘0’ rings, grooves are of proper match so that it gives greater life of ‘0’ ring.

SPEED REDUCTION GEARBOX

  • Eight speed reduction gearbox to achieve different speed for working and travel.

  • All the gearbox are in oil bath and are of proper alloy steel material hardened to get greater life.

  • Gearbox is provided with oil level indicator and oil drain plug for better operation and maintenance.

THICKNESS / LEVEL CONTROL

  • Thickness can be controlled manually by simple switch on screed

BRAKES

  • Brakes can be operated by pushing pedals provided near both the operator’s seat.

  • The safety brakes are acting on the speed shaft, which are coupled to the drive wheels.

FRONT WHEEL

  • Two solid rubber tyre of size 550 mm x 175 mm is mounted directly on chassis one on left and one on right side.

  • Hydraulic steering is fitted for effortless operation.

CONTROL PANEL

  • Fix type operator panel with traveling and operating functions on right side.

  • Single operator seat.

  • Hydraulic steering is fitted for effortless operation.

  • Machine is controlled by means of simple switches on operator panel, valve lever and gear lever near operator seat.

REAR BOGIE

  • Two Nos. tyre size 11.00 x 20, one on either side is mounted directly on chassis.

HOPPER

  • Movement of the two hoppers is obtained by means of hydraulic cylinder operated independently by simple switches of control panel.

  • Hopper Capacity: 4.25 CM

CONVEYOR SYSTEM

  • Two pallet conveyors with hardened steel chain provide the material to two sets of augers which spreads material on both sides.

  • Mechanical drive for conveyor and auger

  • Each of the pallet conveyors can be controlled independently from the operator’s seat.

WORM ASSEMBLY

  • Worm spreads material in front of screed in total width of pavement.

  • Hydraulic drive for conveyor and auger

  • Properly sealed bearings are used for greater life as they are always covered with the laying material while paving.

  • Special arrangement for greasing is provided as greasing is required daily for greater life of bearing.

  • Worm is of Ni-Hard / Hi Chromium steel material, properly heat treated for greater service life.

  • Proper covers for chain are provided for greater service life of chain.

SCREED

  • Basic screed width of 2.5 meter, hydraulically extendable up to 4.5 meter.

  • Main screed is pivoted at the center point of the machine to assure a constant flatness or work on uneven grounds.

  • Lateral mobile plates are hydraulically operated, sliding on chromium plated telescopic cylindrical guides for wear resistance to archive paving width up to extendable limit.

  • Screed plate is 360 mm width, 16 mm thick with provision for heating by 8 LPG burners two on each mobile plate and four nos. on main screed plate.

  • Vibration is provided on screed with fixed frequency.

SHUTTERS AND HYDRAULIC PIPING

  • Shutters are provided on three side of machine which can easily be opened for easy inspection and maintenance of the machine.

  • Filters are kept on outer side of machine for maintenance.

  • Maximum use of MS pipe is done as MS pipes occupy less space; they can be easily clamped and reduces chances of leakage.

THRUST ROLLER

  • Two thrust rollers are fixed on heavy oscillating beam provided on front part of the machine.

share:

Our other products


WP-05 Paver

Uniter Engineering Products

Paver

VM-45 with hydraulic drive for conveyor

Uniter Engineering Products

Belts and Conveyors

VP-05 Paver

Uniter Engineering Products

Paver

UAP-04

Uniter Engineering Products

Paver

VM-45

Uniter Engineering Products

Paver


write a comment


contact info

I-Tech Media Pvt Ltd

Address

604, 6th Floor,

Surya House, Road no.7,

Vidyavihar East,

Mumbai-400077, INDIA.

+91 9821667357 /
+91 9820951287

info@i-techmedia.com

Monday - Friday

10:00 am - 6:30 pm

B2B Purchase

B2B Purchase is India’s No. 1 monthly magazine on project procurement. The one & only of its kind - well-focused, response-driven products & services.

Copyright © 2016 RCMME. All Rights Reserved.